Information Collection Request for Pulp and Paper Sector NSPS and NESHAP - Residual Risk and Technology Review (RTR)

 The U.S. Environmental Protection Agency (EPA) is preparing to initiate a Clean Air Act (CAA) Section 114 request for pulp and paper mills related to reviewing the industry’s New Source Performance Standards (NSPS) and National Emission Standards for Hazardous Air Pollutants (NESHAP) emission standards. The three federal emission standards that are the subject of this information collection include:

  • Standards of Performance for Kraft Pulp Mills (40 CFR Part 60, Subpart BB)
  • National Emission Standards for Hazardous Air Pollutants from the Pulp and Paper Industry (40 CFR Part 63, Subpart S)
  • National Emission Standards for Hazardous Air Pollutants for Chemical Recovery Combustion Sources at Kraft, Soda, Sulfite, and Stand-Alone Semi-chemical Pulp Mills (40 CFR Part 63, Subpart MM)

The purpose of this effort is to determine the affected population of pulp and paper processes and re-evaluate emissions standards for these sources.

Information Request Requirements

On December 7, 2010, EPA announced that it had submitted the Information Collection Request (ICR) to the Office of Management and Budget (OMB) for review and approval. The information request would apply to “major sources” and “synthetic area sources” of hazardous air pollutants (HAP). There are 386 mills across the U.S. targeted to receive the pulp and paper sector survey. The survey will be divided into three parts, each with different due dates as summarized in the table below.

Part

Description

Deadline

I

Mill Overview and Subpart S Data

30 days

II

National Emission Inventory (NEI) Update

100 days

III

Chemical Recovery Combustion Sources

180 days

 

Part I of the survey is due back to the EPA 30 days after receipt and will consist of information relevant to the Subpart S review, including: 

  • General mill information and flow diagrams
  • Processes and products
  • Equipment, controls, and compliance options in use for pulp and paper production equipment
  • Permit limits
  • Emissions test data for pulp and paper processing equipment
  • Continuous emission monitoring system (CEMS) data
  • Control cost information

Part II of the survey consists of a National Emission Inventory (NEI) update, which is due back to the EPA 100 days after receipt. Data sets derived from the National Scale Air Toxics Assessment (NATA) NEI will be used for the EPA’s Residual Risk and Technology Review. If 2005 NATA NEI data sets exist for your mill, then some of the information in this spreadsheet will already be populated.

Finally, Part III of the survey requests information regarding chemical recovery combustion sources, for those mills that operates a recovery unit, and is due back to the EPA 180 days after receipt.

Background

As required by the Clean Air Act, EPA must set industry air pollution standards that are up-to-date, ensuring that the standards reflect the newest available technology and provide protection for human health and the environment. EPA must also perform “residual risk” assessments for the Maximum Achievable Control Technology (MACT) standards, under the NESHAPS, to analyze the public health impacts that remain once all required MACT controls have been put in place. The agency must review these standards and perform residual risk assessments every eight years. Since the pulp and paper industry’s current MACT standards were finalized in 1998 and 2001, the EPA is currently behind schedule in these reviews.

As a result of a January 2009 lawsuit regarding the delay in the required MACT reviews, a July 6, 2010 court settlement establishes a schedule for EPA to complete the residual risk review for the pulp and paper industry. By June 15, 2011, EPA must issue proposed revisions to the pulp and paper NESHAP and propose residual risk standards or sign proposed determinations that such standards are not required. By December 16, 2011, EPA must finalize the NESHAP revisions and risk standards or finalize the determinations that these are not required.

Comments EPA received during the public comment period were related to concerns over EPA collecting more information than is necessary, EPA underestimating the cost burden to the industry for the information collection, and the short time frame and heavy reporting period in which mills would be expected to respond. On November 16, 2010, the EPA addressed these comments and made significant changes to the survey in an effort to decrease its burden, including dividing the survey into the three parts, as described previously, and making several sections optional. EPA announced on December 7, 2010, that it had submitted the ICR to the OMB for review and approval.

Any rulemaking that results from this standards review presents a potential impact on a facility’s capital planning. A newly proposed rule could tighten emissions control standards and require air pollution control equipment upgrades. Once promulgated, facilities typically have three years to comply.

For more information, see the Federal Register notice (75 FR 76005, 12/7/2010) regarding Agency Information Collection Activities: Proposed Collection; Comment Request; Information Request for Pulp and Paper Sector New Source Performance Standards (NSPS) and National Emission Standards for Hazardous Air Pollutants (NESHAP) Residual Risk and Technology Review. Other sectors that face review include aerospace, furniture, aluminum production, cement manufacturing, lead smelting, pesticide manufacturing, pharmaceuticals production and shipbuilding.

Section 114 Response Support

Trinity has assisted multiple clients in the pulp and paper industry and other sectors in the preparation of responses to Section 114 ICRs. In support of these requests, Trinity has assisted clients with services such as: commenting on previous and proposed Section 114 responses; Section 114 response submittals; reviews of a company’s facility and corporate environmental files; reviews of regulatory agency files for a facility; historical Prevention of Significant Deterioration (PSD) applicability determinations; control device and process information summaries; performing and checking emission inventories; development of economic data; and quality assurance reviews of submissions. For assistance, contact your local Trinity office at (800) 229-6655.